Nanovna 50kHz~1000MHz Vector Network Analyzer UHF HF VNA UV VHF Antenna Analyzer

Description

Product Description:
Specification:
Size: 14CM * 7.5CM * 2CM (length, width and height)
Measuring Frequency: 50kHz ~ 1000MHz
RF output: - 13 DBM (maximum - 9 dbm)
Frequency accuracy: < 0.5 ppm
Port SWR: < 1.1
Display: 4.3 inch IPS TFT (800x480)
USB Interface: USB Type-C Communication Mode: CDC (Serial)
Power consumption: USB 5V 200mA, built-in 5000mAh battery, theoretical life of 18 hours, maximum charging current 2A
Output capability: 5V/1A, supporting Android and Apple phones
Number of calibration points: 101
Number of scanning points: 101
Display Tracking: 4, Mark: 4, Settings Save: 5
Scanning time: about 1.9s/time (50kHz-1000MHz full frequency band)
Measurable S parameters, voltage standing wave ratio SWR, phase diagram, group delay, Smith circle diagram... ;
19.0Wh (about 5000mAh after conversion) large capacity lithium battery
Designing a metal shield for the RF front end, allowing the S21 to have a dynamic range better than 60dB over the full frequency range
power bank fuction: 5V/1A , Supporting Android and Apple Mobile
Open route length test:
NanoVNA-F S11 parameter, SWR standing wave ratio test
UV9D antenna U-band standing wave ratio measurement, starting frequency: 300M, termination frequency: 600M, standing wave minimum frequency 441.000000MHz, SWR = 1.03.
S21 insertion loss measurement, low pass, high pass, band pass filter measurement
Measuring 6.5M Ceramic Notch with NanoVNA-F
Measuring 10.7M ceramic filter using NanoVNA-F
A self-made low-pass filter was measured using the NanoVNA-F with a 3dB bandwidth of approximately 400MHz.
Performance comparison, E5071C four-port vector network vs NanoVNA-F
Color:As the picture
Features:
NanoVNA-F Mini Vector Network Analyser is a product based on the Open Source Project of NanoVNA. The RF part is consistent with the original version (NanoVNA-F uses harmonic spread measurement frequency to 1 GHz).
NanoVNA-F hardware functions include and are not limited to the following improvements:
1. Use 4.3-inch IPS TFT LCD screen, with a larger view angle and can be seen clearly in strong outdoor light.
2. Switch to large capacity 5000mAh lithium battery, standby time is longer, and expand a USB interface. Usually, it can be used as a rechargeable treasure when the instrument is not used.
3. The IC is charged by high current 2A, and the charging time is shorter.
4. Change to larger and better operating wave wheel.
5. Switch to a power switch with a greater sense of operation and a better sense of operation.
6. Support Chinese and English menu switching;
7. Upgrade the user program by virtual U disk.
8. Standard aluminium shell to protect SMA head and reduce the interference of external electromagnetic wave to instrument.
9. Software open source github.com/flyoob/NanoVNA-F
The hardware block diagram of NanoVNA-F is as follows
NanoVNA-F measurement range is 50k-1GHz. The harmonic spread measurement frequency of the output signal of the clock chip SI5351 is 1000MHz. At 600M-1GHz, the dynamic range of S11 is 40dB (standing wave ratio is less than 1.02). At the same time, a metal shield is designed for the RF front-end, so that the dynamic range of S21 is better than 60dB in the whole frequency band.
Tips:
Please allow minor deviation due to manual measurement.
Due to the difference between different monitors, the picture may not reflect the actual color of the item.
Package Include
:
1x Nanovna meter
2x SMA-JJ RG316 cable 20CM (NanoVNA-F is a standard SMA female connector, which is used to switch to M head and N head to better protect SMA female)
1 set of calibration parts (50Ω standard load x1, open circuit calibration piece x1, short circuit calibration piece x1, use the included calibration piece, the instrument can be calibrated to get good measurement result data)
1x SMA-JJ double needle
1x SMA elbow external screw inner hole to inner screw inner needle
1x Type-C data cable
Shipping:
Shipping Estimated Delivery Time
*Economy(without tracking): 15-45 business days
*Speedpak(with tracking): 10-20 business days
*EMS/DHL(with tracking): 7-10 business days, need to pay extra shipping cost
For faraway region or countries (Brazil, Mexico, Peru, etc), the transit time may be longer than Overall Transit Time Frame.
Notes, the delivery time may vary due to public holidays, natural disasters, customs issue and other unexpected impact, etc.
Customs Declaration:
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.
Please check with your country’s customs office to determine what these additional costs will be prior to biddingying.
Payment:
We accept PayPal ONLY currently. Payment must be made within 4 business days.
If you do not have Paypal account, please register at (www.paypal.com).
Return & Refund:
Returns are accepted within 30/60 days.
Please read the item description and check the pictures carefully before bidding. Return or refund is available only if item DOA or there's error in item description
causing the item not fitting your need. In such cases, seller pays for all related shipping cost if any.
Returns are also acceptable if buyer purchased this by mistake and item still in good condition for reselling. Buyer is responsible for all related shipping cost.
Feedback:
As long as you are satisfied with your purchase, please kindly leave us a 5 stsrs Positive Feedback, as it is very important for our store performance.
If there is any problem with your order, please contact us and give us a chance to resolve your problem Before leaving us a negative feedback.